THOMSON MO6 SOUND CARD

Placez ici vos trucs et astuces, étalez sans retenue votre savoir-faire et votre science qui va nous permettre de redonner une apparence neuve et fonctionnelle à nos bouzes.

Modérateurs : Papy.G, fneck, Carl

Répondre
dinoprodest
Messages : 312
Inscription : 01 févr. 2020 20:31
Localisation : Rome - Italy

THOMSON MO6 SOUND CARD

Message par dinoprodest »

Good morning everybody,
in your opinion, is it possible to build a sound card expansion based on sound programmable chip ?
__sam__
Messages : 7923
Inscription : 18 sept. 2010 12:08
Localisation : Brest et parfois les Flandres

Re: THOMSON MO6 SOUND CARD

Message par __sam__ »

Have a look at the TripleX project discussed in this thread.
Samuel.
A500 Vampire V2+ ^8^, A1200 (030@50mhz/fpu/64mb/cf 8go),
A500 GVP530(MMU/FPU) h.s., R-Pi, TO9, TO8D, TO8.Démos
dinoprodest
Messages : 312
Inscription : 01 févr. 2020 20:31
Localisation : Rome - Italy

Re: THOMSON MO6 SOUND CARD

Message par dinoprodest »

Thonson MO6 hardware question.
When i write a data from address A7C0 to A7CF, the gate-array reset the A7CX signal ?
dinoprodest
Messages : 312
Inscription : 01 févr. 2020 20:31
Localisation : Rome - Italy

Re: THOMSON MO6 SOUND CARD

Message par dinoprodest »

I'am tryng to build a sound card for thomson mo6.
Schematic attached. Can it run ?
What do you think ?
Pièces jointes
MO6_SND-1.png
MO6_SND-1.png (18.45 Kio) Consulté 9900 fois
Avatar de l’utilisateur
jb_jb_fr
Messages : 391
Inscription : 29 mars 2010 10:36
Localisation : Essonne (91)
Contact :

Re: THOMSON MO6 SOUND CARD

Message par jb_jb_fr »

For me this scheme can't works because the R/W signal is missing.
A write operation can occurs during a Read operation due to this missing signal :-(
And the 74373 is not necessary because the 76489 is only used during write operation.
No read operation can be done.
This scheme could be simplified.
My proposal is the following
MO6_SND-1_JB.png
MO6_SND-1_JB.png (17.1 Kio) Consulté 9836 fois
Jacques
dinoprodest
Messages : 312
Inscription : 01 févr. 2020 20:31
Localisation : Rome - Italy

Re: THOMSON MO6 SOUND CARD

Message par dinoprodest »

Merci, le / RW vous avez raison, mais la raison d'utiliser le 74373 est que le bus de données doit rester stable pendant 32 cycles d'horloge :D
dinoprodest
Messages : 312
Inscription : 01 févr. 2020 20:31
Localisation : Rome - Italy

Re: THOMSON MO6 SOUND CARD

Message par dinoprodest »

supprimé certaines adresses inutiles et ajouté / RW et E
Pièces jointes
MO6_SND-2.png
MO6_SND-2.png (18.32 Kio) Consulté 9825 fois
Avatar de l’utilisateur
jice
Messages : 213
Inscription : 21 avr. 2014 15:08
Localisation : Madrid

Re: THOMSON MO6 SOUND CARD

Message par jice »

Hello

Excellent idea :) I wish they had done that in the time, we would have had music and sfx in the games :D

I started something similar a while ago: viewtopic.php?f=18&t=10848
but had no time to go further than what is in the post.

May I ask why the SN76489 and not e.g. the AY-3?

++
MO5 - MO5 Platini - TO7 - TO7/70 - TO8 - TO9+
dinoprodest
Messages : 312
Inscription : 01 févr. 2020 20:31
Localisation : Rome - Italy

Re: THOMSON MO6 SOUND CARD

Message par dinoprodest »

Hi,
we have got the same idea. SN76489 because is the first i have found on google, searching sound programmable chip. I have seen the datasheet, and i have chosen it for its properties. I think it should be simple to build and program with asm or Poke instructions.
I have also seen YM2612 but it has too much registers.
Avatar de l’utilisateur
jice
Messages : 213
Inscription : 21 avr. 2014 15:08
Localisation : Madrid

Re: THOMSON MO6 SOUND CARD

Message par jice »

do you have some examples of tunes tunes using this chip?
MO5 - MO5 Platini - TO7 - TO7/70 - TO8 - TO9+
dinoprodest
Messages : 312
Inscription : 01 févr. 2020 20:31
Localisation : Rome - Italy

Re: THOMSON MO6 SOUND CARD

Message par dinoprodest »

https://youtu.be/4m38570sYJA

This is an example, by searching on youtube channel. :)
Now i have got all components ill build the cards as fast as possible.
After i'll test the board with stm32 microcontroller, after follow the test on pc 128.
Pièces jointes
IMG_20201018_103607.jpg
IMG_20201018_103607.jpg (259.65 Kio) Consulté 9361 fois
Avatar de l’utilisateur
jice
Messages : 213
Inscription : 21 avr. 2014 15:08
Localisation : Madrid

Re: THOMSON MO6 SOUND CARD

Message par jice »

I'm impressed, you already have built it!
You have 19x2 connectors I can see ;)

the tunes are good, Sonic are good memories :)

Did you think to inject the sound to the sound pin of the extension bus, so that the Thomson will mix it with its own sound and output it to Peritel?
MO5 - MO5 Platini - TO7 - TO7/70 - TO8 - TO9+
dinoprodest
Messages : 312
Inscription : 01 févr. 2020 20:31
Localisation : Rome - Italy

Re: THOMSON MO6 SOUND CARD

Message par dinoprodest »

:D no, i have only soldered the dip sockets, i have to connect all the wires. Yes i decide to connect the audio output to expansion port.
Avatar de l’utilisateur
jice
Messages : 213
Inscription : 21 avr. 2014 15:08
Localisation : Madrid

Re: THOMSON MO6 SOUND CARD

Message par jice »

Great! I'm impatient to see it working!
MO5 - MO5 Platini - TO7 - TO7/70 - TO8 - TO9+
dinoprodest
Messages : 312
Inscription : 01 févr. 2020 20:31
Localisation : Rome - Italy

Re: THOMSON MO6 SOUND CARD

Message par dinoprodest »

when i have any news i'll post a demo with results.
I hope i haven''t any signals timing issues. :D
Répondre