mon nouveau lecteur 1541 - 1581 / Pi1541
Modérateurs : Papy.G, fneck, Carl
- sayasupacrew
- Messages : 332
- Inscription : 02 avr. 2011 15:07
- Localisation : noirmoutier
Re: mon nouveau lecteur 1541 - 1581 / Pi1541
j'ai petit problème avec le pi1541
dans le fichier config.txt
si je commente l'option //splitIECLines = 1 (j'ai l'oled qui fonctionne, mais je ne peu plus correspondre entre le pi1541 et le c64.)
et inversement si je commente la splitIECLines = 1, je n'est plus d'affichage oled mais je peu charger les jeux du c64 depuis le pi1541.
saya
dans le fichier config.txt
si je commente l'option //splitIECLines = 1 (j'ai l'oled qui fonctionne, mais je ne peu plus correspondre entre le pi1541 et le c64.)
et inversement si je commente la splitIECLines = 1, je n'est plus d'affichage oled mais je peu charger les jeux du c64 depuis le pi1541.
saya
Re: mon nouveau lecteur 1541 - 1581 / Pi1541
Essaye ça:
// If you are using the split line hardware option (ie Option B) then you need to specify this option
//splitIECLines = 1
// If you are using some type of hardware that requires the lines to be inverted then specify these options here
invertIECInputs = 1
// If you are using the split line hardware option (ie Option B) then you need to specify this option
//splitIECLines = 1
// If you are using some type of hardware that requires the lines to be inverted then specify these options here
invertIECInputs = 1
Auteur de la rubrique Rétro Jeux-video dans Pif magazine
Ma vie de Retrogamer Suivez le blog sur Facebook
Ma vie de Retrogamer Suivez le blog sur Facebook
- sayasupacrew
- Messages : 332
- Inscription : 02 avr. 2011 15:07
- Localisation : noirmoutier
Re: mon nouveau lecteur 1541 - 1581 / Pi1541
avec ces options turk j'ai l'oled, pas de comunication en pi1541 et c64.
Re: mon nouveau lecteur 1541 - 1581 / Pi1541
Et comme ça?
// If you are using the split line hardware option (ie Option B) then you need to specify this option
splitIECLines = 1
// If you are using some type of hardware that requires the lines to be inverted then specify these options here
invertIECInputs = 1
// If you are using the split line hardware option (ie Option B) then you need to specify this option
splitIECLines = 1
// If you are using some type of hardware that requires the lines to be inverted then specify these options here
invertIECInputs = 1
Auteur de la rubrique Rétro Jeux-video dans Pif magazine
Ma vie de Retrogamer Suivez le blog sur Facebook
Ma vie de Retrogamer Suivez le blog sur Facebook
- sayasupacrew
- Messages : 332
- Inscription : 02 avr. 2011 15:07
- Localisation : noirmoutier
Re: mon nouveau lecteur 1541 - 1581 / Pi1541
la j'ai
pas l'oled, '? device no present error' quand je tape load"*",8
pas l'oled, '? device no present error' quand je tape load"*",8
Re: mon nouveau lecteur 1541 - 1581 / Pi1541
Mais ça n'a rien à voir l'Oled avec le Device not present
Device not present c'est que le Commodore ne voit pas le lecteur, t'es sur que tu n'as pas activé cette ligne et que tu as mis ton lecteur en 9 ?:
// If you would like to change the drive number then specify it here (8 is the default)
//deviceID = 9
Device not present c'est que le Commodore ne voit pas le lecteur, t'es sur que tu n'as pas activé cette ligne et que tu as mis ton lecteur en 9 ?:
// If you would like to change the drive number then specify it here (8 is the default)
//deviceID = 9
Auteur de la rubrique Rétro Jeux-video dans Pif magazine
Ma vie de Retrogamer Suivez le blog sur Facebook
Ma vie de Retrogamer Suivez le blog sur Facebook
- sayasupacrew
- Messages : 332
- Inscription : 02 avr. 2011 15:07
- Localisation : noirmoutier
Re: mon nouveau lecteur 1541 - 1581 / Pi1541
nop, j'ai sa le fichier option.txt
//deviceID = 9
je peu t'envoyez le fichiet option.txt.
http://helen.vivet.free.fr/Samolita/options.txt
//deviceID = 9
je peu t'envoyez le fichiet option.txt.
http://helen.vivet.free.fr/Samolita/options.txt
Dernière modification par sayasupacrew le 04 juin 2023 03:31, modifié 2 fois.
Re: mon nouveau lecteur 1541 - 1581 / Pi1541
Enlève les commentaires et met 1 pour voir:
//If you are using a 7407
//invertIECOutputs = 0
Et puis, si tu ne mets pas ta ROM ca ne peut pas marcher:
// By default Pi1541 will search the root of the SD card for a ROM file and use this for ROM1.
// The first file found with either of the following names will be used; d1541.rom, dos1541, d1541II, Jiffy.bin
// You can override the default ROM1 by specifying it here
//ROM1 = YourDefaultRom (METTRE TA ROM ICI)
Mon Option.txt:
// Sample options.txt configuration file for Pi1541
// If you would like to change the drive number then specify it here (8 is the default)
//deviceID = 9
// If you are using the split line hardware option (ie Option B) then you need to specify this option
splitIECLines = 1
// If you are using some type of hardware that requires the lines to be inverted then specify these options here
//invertIECInputs = 1
//If you are using a 7407
invertIECOutputs = 1
// If you are using the Pi's composite video out then these options allow you to experiment with the display resolution
//ScreenWidth = 512
//ScreenHeight = 384
// By default Pi1541 will search the root of the SD card for a ROM file and use this for ROM1.
// The first file found with either of the following names will be used; d1541.rom, dos1541, d1541II, Jiffy.bin
// You can override the default ROM1 by specifying it here
ROM1 = dos1541
// You can specify additional ROMS here (up to 7)
// You can then use the function keys (F1-F7) on the keyboard to change which one you would like to use (only in browse mode and not in emulation mode)
// You can also use the buttons to swap ROMs by holding down button 1 and pressing one other buttons 2-5
// .LST files can also specify one of these ROMS that will automatically be selected when the LST file is loaded.
//ROM2 = dos1541
//ROM3 = d1541II
// Reference you 1581 ROM here
ROM1581 = 1581-rom.318045-02.bin
//ROM1581 = JiffyDOS_1581.bin
// The rate (in seconds) a long selection is scrolled
scrollHighlightRate = 0.07
// Enable RAMBoard emulation - 8k drive RAM expansion at 0x8000
//RAMBOard = 1
ChargenFont = chargen // 8 bit font file
// If using CBMFileBrowser then it is best to specify this option. When the computer resets the Pi will always revert back to the root folder ready to load CBMFileBrowser again.
OnResetChangeToStartingFolder = 1
// If you use FB64 (CBMFileBrowser) and want to use a fast loader cartridge (AR6, EFL, FC3) to load it then use this option to automatically mount it.
//AutoMountImage = fb.d64 // You MUST have a disk image in \1541 with this filename
// If you use FB64 (CBMFileBrowser) and want Pi1541 to send all file names as lower case.
LowercaseBrowseModeFilenames = 1
// If you are using a FB128 in 128 mode you can get FB128 to auto boot using this option
//AutoBootFB128 = 1
// If you are using a 128 you can auto boot anything using this option
// This over-rides AutoBootFB128
//128BootSectorName = bootsect.128
// If you would ever like to disable browse mode completely you can do so here
//DisableSD2IECCommands = 1
// This option displays the IEC bus activity on the bottom of the Pi's screen
//GraphIEC = 0
// If you have hardware with a peizo buzzer (the type without a generator) then you can use this option to hear the head step
SoundOnGPIO = 1
SoundOnGPIODuration = 100 // Length of buzz in micro seconds
SoundOnGPIOFreq = 200 // Frequency of buzz in Hz
// You can create 320x200 PNG files with the same name as your disk images. With this option turned on they will be displayed on the Pi's screen.
//DisplayPNGIcons = 1
// If you would like to specify what file will be loaded by LOAD"*" in browse mode then specify it here
//StarFileName = somefile
// Alt-N creates a new disk image.
// Names are formed automatically as autoname001.d64, autoname002.d64 etc...
// change the base of the filename here
//AutoBaseName = autoname
// By default Alt-N creates a new D64 disk image.
// If you rather it create a G64 then use this option.
//NewDiskType = g64
// If you are using a LCD screen then specify it here
//LCDName = ssd1306_128x64
//LCDName = ssd1306_128x32
LCDName = sh1106_128x64
// If you are using a LCD screen and you would like PageUp and PageDown keys to work with it (rather than the HDMI screen) then specify this option
//KeyboardBrowseLCDScreen = 1
// change startup logo on oled - 1541ii or 1541classic
//LcdLogoName = 1541ii
LcdLogoName = 1541classic
//LcdLogoName = customfile.raw
// If you are using I2C LCD you can optionally change what pins it is connected to.
// (defaults to 0 for non-split lines (Option A) or 1 for split lines (Option B))
//i2cBusMaster = 0 //SDA - pin 27 SCL - pin 28
i2cBusMaster = 1 //SDA - pin 3 SCL - pin 5
//i2cLcdAddress = 60 // I2C display address in decimal and shifted. 60 == 0x78, 61 == 0x7A
//i2cLcdFlip = 1 // Rotate i2c LCD screen 180 degrees
//i2cLcdOnContrast = 127 // Allows you to adjust the contrast on your i2c LCD screen
//i2cScan = 1 // scan i2c bus and display addresses on screen
//i2cLcdUseCBMChar = 0 // set it to 1 to use CBM font on LCD. Small but fun !
//QuickBoot = 0 // faster startup
//ShowOptions = 0 // display some options on startup screen
//IgnoreReset = 0
// You can remap the physical button functions
// numbers correspond to the standard board layout
//buttonEnter = 1
//buttonUp = 2
//buttonDown = 3
//buttonBack = 4
//buttonInsert = 5
//ROTARY:
//
// KY-040 Rotary Encoder Support
//
// If you would like to use a KY-040 Rotary Encoder for browse menu up/down
// and select, you can enable it here. Connect as follows:
//
// GPIO 22 - Menu up - Encoder pin A (CLK)
// GPIO 23 - Menu down - Encoder pin B (DT)
// GPIO 27 - Enter/Select - Encoder pushbutton (SW)
//
// ** Using an encoder is incompatible with the button remapping. You must
// use the default values of Enter=1, Up=2, Down=3, Back=4 and Insert=5.
//
// ** This has only been tested using a Raspberry Pi 3. Earlier models may
// or may not work as expected!
//
// Please see dmRotary.h for full implementation details.
//
//RotaryEncoderEnable = 1
// This option will display the temperature of the Pi's CPU.
// It should be about 52°C anything above 65°C is bad and there is something wrong with your hardware
//DisplayTemperature = 1
//If you are using a 7407
//invertIECOutputs = 0
Et puis, si tu ne mets pas ta ROM ca ne peut pas marcher:
// By default Pi1541 will search the root of the SD card for a ROM file and use this for ROM1.
// The first file found with either of the following names will be used; d1541.rom, dos1541, d1541II, Jiffy.bin
// You can override the default ROM1 by specifying it here
//ROM1 = YourDefaultRom (METTRE TA ROM ICI)
Mon Option.txt:
// Sample options.txt configuration file for Pi1541
// If you would like to change the drive number then specify it here (8 is the default)
//deviceID = 9
// If you are using the split line hardware option (ie Option B) then you need to specify this option
splitIECLines = 1
// If you are using some type of hardware that requires the lines to be inverted then specify these options here
//invertIECInputs = 1
//If you are using a 7407
invertIECOutputs = 1
// If you are using the Pi's composite video out then these options allow you to experiment with the display resolution
//ScreenWidth = 512
//ScreenHeight = 384
// By default Pi1541 will search the root of the SD card for a ROM file and use this for ROM1.
// The first file found with either of the following names will be used; d1541.rom, dos1541, d1541II, Jiffy.bin
// You can override the default ROM1 by specifying it here
ROM1 = dos1541
// You can specify additional ROMS here (up to 7)
// You can then use the function keys (F1-F7) on the keyboard to change which one you would like to use (only in browse mode and not in emulation mode)
// You can also use the buttons to swap ROMs by holding down button 1 and pressing one other buttons 2-5
// .LST files can also specify one of these ROMS that will automatically be selected when the LST file is loaded.
//ROM2 = dos1541
//ROM3 = d1541II
// Reference you 1581 ROM here
ROM1581 = 1581-rom.318045-02.bin
//ROM1581 = JiffyDOS_1581.bin
// The rate (in seconds) a long selection is scrolled
scrollHighlightRate = 0.07
// Enable RAMBoard emulation - 8k drive RAM expansion at 0x8000
//RAMBOard = 1
ChargenFont = chargen // 8 bit font file
// If using CBMFileBrowser then it is best to specify this option. When the computer resets the Pi will always revert back to the root folder ready to load CBMFileBrowser again.
OnResetChangeToStartingFolder = 1
// If you use FB64 (CBMFileBrowser) and want to use a fast loader cartridge (AR6, EFL, FC3) to load it then use this option to automatically mount it.
//AutoMountImage = fb.d64 // You MUST have a disk image in \1541 with this filename
// If you use FB64 (CBMFileBrowser) and want Pi1541 to send all file names as lower case.
LowercaseBrowseModeFilenames = 1
// If you are using a FB128 in 128 mode you can get FB128 to auto boot using this option
//AutoBootFB128 = 1
// If you are using a 128 you can auto boot anything using this option
// This over-rides AutoBootFB128
//128BootSectorName = bootsect.128
// If you would ever like to disable browse mode completely you can do so here
//DisableSD2IECCommands = 1
// This option displays the IEC bus activity on the bottom of the Pi's screen
//GraphIEC = 0
// If you have hardware with a peizo buzzer (the type without a generator) then you can use this option to hear the head step
SoundOnGPIO = 1
SoundOnGPIODuration = 100 // Length of buzz in micro seconds
SoundOnGPIOFreq = 200 // Frequency of buzz in Hz
// You can create 320x200 PNG files with the same name as your disk images. With this option turned on they will be displayed on the Pi's screen.
//DisplayPNGIcons = 1
// If you would like to specify what file will be loaded by LOAD"*" in browse mode then specify it here
//StarFileName = somefile
// Alt-N creates a new disk image.
// Names are formed automatically as autoname001.d64, autoname002.d64 etc...
// change the base of the filename here
//AutoBaseName = autoname
// By default Alt-N creates a new D64 disk image.
// If you rather it create a G64 then use this option.
//NewDiskType = g64
// If you are using a LCD screen then specify it here
//LCDName = ssd1306_128x64
//LCDName = ssd1306_128x32
LCDName = sh1106_128x64
// If you are using a LCD screen and you would like PageUp and PageDown keys to work with it (rather than the HDMI screen) then specify this option
//KeyboardBrowseLCDScreen = 1
// change startup logo on oled - 1541ii or 1541classic
//LcdLogoName = 1541ii
LcdLogoName = 1541classic
//LcdLogoName = customfile.raw
// If you are using I2C LCD you can optionally change what pins it is connected to.
// (defaults to 0 for non-split lines (Option A) or 1 for split lines (Option B))
//i2cBusMaster = 0 //SDA - pin 27 SCL - pin 28
i2cBusMaster = 1 //SDA - pin 3 SCL - pin 5
//i2cLcdAddress = 60 // I2C display address in decimal and shifted. 60 == 0x78, 61 == 0x7A
//i2cLcdFlip = 1 // Rotate i2c LCD screen 180 degrees
//i2cLcdOnContrast = 127 // Allows you to adjust the contrast on your i2c LCD screen
//i2cScan = 1 // scan i2c bus and display addresses on screen
//i2cLcdUseCBMChar = 0 // set it to 1 to use CBM font on LCD. Small but fun !
//QuickBoot = 0 // faster startup
//ShowOptions = 0 // display some options on startup screen
//IgnoreReset = 0
// You can remap the physical button functions
// numbers correspond to the standard board layout
//buttonEnter = 1
//buttonUp = 2
//buttonDown = 3
//buttonBack = 4
//buttonInsert = 5
//ROTARY:
//
// KY-040 Rotary Encoder Support
//
// If you would like to use a KY-040 Rotary Encoder for browse menu up/down
// and select, you can enable it here. Connect as follows:
//
// GPIO 22 - Menu up - Encoder pin A (CLK)
// GPIO 23 - Menu down - Encoder pin B (DT)
// GPIO 27 - Enter/Select - Encoder pushbutton (SW)
//
// ** Using an encoder is incompatible with the button remapping. You must
// use the default values of Enter=1, Up=2, Down=3, Back=4 and Insert=5.
//
// ** This has only been tested using a Raspberry Pi 3. Earlier models may
// or may not work as expected!
//
// Please see dmRotary.h for full implementation details.
//
//RotaryEncoderEnable = 1
// This option will display the temperature of the Pi's CPU.
// It should be about 52°C anything above 65°C is bad and there is something wrong with your hardware
//DisplayTemperature = 1
Auteur de la rubrique Rétro Jeux-video dans Pif magazine
Ma vie de Retrogamer Suivez le blog sur Facebook
Ma vie de Retrogamer Suivez le blog sur Facebook
- sayasupacrew
- Messages : 332
- Inscription : 02 avr. 2011 15:07
- Localisation : noirmoutier
Re: mon nouveau lecteur 1541 - 1581 / Pi1541
turk: je t'envoi un dump de ma carte sd. http://helen.vivet.free.fr/Pc/PI1541/pi ... 100623.zip.
Dernière modification par sayasupacrew le 10 juin 2023 20:58, modifié 2 fois.
Re: mon nouveau lecteur 1541 - 1581 / Pi1541
Je regarderai ça mais as-tu fait les modifications que je te commente dans mon post antérieur?
Auteur de la rubrique Rétro Jeux-video dans Pif magazine
Ma vie de Retrogamer Suivez le blog sur Facebook
Ma vie de Retrogamer Suivez le blog sur Facebook
- sayasupacrew
- Messages : 332
- Inscription : 02 avr. 2011 15:07
- Localisation : noirmoutier
Re: mon nouveau lecteur 1541 - 1581 / Pi1541
oui
il fallais mettre l'option i2cBusMaster = 0 //SDA - pin 27 SCL - pin 28 pour que je puisse avoir l'oled d'allummer et la comunication avec le c64 et le pi1541.
tu veu me faire plaisir vas sur mon sute helen.vivet.free.fr et clic sur 'clic here' et attendre 5mm stp.
j'ai vue sur ton blog que tu as la memes carte que moi, j'ai reçu le botier la semaine dernière.
il fallais mettre l'option i2cBusMaster = 0 //SDA - pin 27 SCL - pin 28 pour que je puisse avoir l'oled d'allummer et la comunication avec le c64 et le pi1541.
tu veu me faire plaisir vas sur mon sute helen.vivet.free.fr et clic sur 'clic here' et attendre 5mm stp.
j'ai vue sur ton blog que tu as la memes carte que moi, j'ai reçu le botier la semaine dernière.
Re: mon nouveau lecteur 1541 - 1581 / Pi1541
Excellente carte
Auteur de la rubrique Rétro Jeux-video dans Pif magazine
Ma vie de Retrogamer Suivez le blog sur Facebook
Ma vie de Retrogamer Suivez le blog sur Facebook
- sayasupacrew
- Messages : 332
- Inscription : 02 avr. 2011 15:07
- Localisation : noirmoutier
Re: mon nouveau lecteur 1541 - 1581 / Pi1541
turk182
j'aime bien ton blog.
j'aime bien ton blog.
Re: mon nouveau lecteur 1541 - 1581 / Pi1541
Merci beaucoup ! Ça fait plaisir
Auteur de la rubrique Rétro Jeux-video dans Pif magazine
Ma vie de Retrogamer Suivez le blog sur Facebook
Ma vie de Retrogamer Suivez le blog sur Facebook
- sayasupacrew
- Messages : 332
- Inscription : 02 avr. 2011 15:07
- Localisation : noirmoutier
Re: mon nouveau lecteur 1541 - 1581 / Pi1541
turk182:
je me suis acheter une 'SD card reader' pour VCS, j'ai l'impression que ça n'est pas courrant.
Sy
as tu des doublons ou des machines dont tu ne désire plus, jette un oeil sur mon listing. http://helen.vivet.free.fr/subdirB/listingTom.html
je me suis acheter une 'SD card reader' pour VCS, j'ai l'impression que ça n'est pas courrant.
Sy
as tu des doublons ou des machines dont tu ne désire plus, jette un oeil sur mon listing. http://helen.vivet.free.fr/subdirB/listingTom.html
Dernière modification par sayasupacrew le 21 sept. 2023 18:39, modifié 2 fois.